This industrial strength MIG delivers 356 Amps of pure power, plus all the features needed to maximise your productivity in one complete package.
Productivity on Demand
Experience a boost in productivity thanks to the impressive 40% duty cycle at the rated output of 32 Volts.
The Weldmatic 356 is the ideal choice for medium industrial fabrication workshops, sheet metal, boat building, service, repair, maintenance and training centres/schools.
Fitted with an industrial standard 3.6m gun and cable for reliable welding performance and long operating life.
Fine Arc Control
30 Voltage steps provide fine arc control over the whole operating range, from short arc to full spray transfer.
Reach around those awkward jobs with the fully enclosed separate wirefeeder.
Built-in Operator Safety
The power source features a built-in thermal protection device that will cut in if the machine is operated beyond its safe thermal operating zone.
Gas or Gasless
Suits gas shielded and flux cored wires.
Dual Front Handles
Exclusive split handles with rubber grips designed to move the machine easily and allow composite work lead and MIG gun to be stored independently.
The Fan-on-Demand™ uses less power and generates less noise by only operating the fan when needed. This reduces dust build up inside the machine, meaning less maintenance time and increasing the life of components.
5kg & 15kg.
Heavy Duty 4 Roll Drive System
Now with larger, stronger gears and ball bearings to further enhance the reliability and performance of Weldmatic machines.
Quick and Easy Gun Cable Connection
All Weldmatic machines are supplied with an industrial quality gun and cable, complete with euro connector for easy fitting and removal.
By only operating when needed, the fun uses less power and generates less noise. The result is a reduction in dust build-up inside the machine, meaning less maintenance time and longer component time.
Packed 4RD Wirefeeder
W64 wirefeeder enables custom set-up to suit the job – including arc start, low wire speed, burnback, spot time, trigger latch, inch, purge, and pre and post gas.
Easy Screw Spool Hub
A new addition to the Weldmatic range is the easy screw spool hub, allowing for quick installation of 5 and 15kg spools.
Gas or Gasless
Suited to both gas shielded solid wires and gasless (self-shielding) flux cored wires. Industrial front mount strength connectors make the switch between shielded and gasless wires quick and easy.
Superior Inductance Technology
Weldmatic machines have been engineered to deliver smooth arc performance right across the welding range.
Low Gas Cylinder Tray
The low, easy to access rear tray, allows the gas bottle to be rolled on and off with ease, eliminating the need for lifting.
Heavy Duty Transformer
Engineered for reliability, the heavy duty transformer delivers a smooth, consistent weld performance.
Fold down tool tray provides storage for gun contact tips and nozzles.
Dual Front Handles
Dual handles make it easy to move your Weldmatic around the workshop, plus provide handy storage for interconnecting work leads.
- W64 4 Roll Drive Wirefeeder
- 3.6m Euro Gun Cable
- Bernard™ Centerfire™ Tip 0.9mm
- 10m Work Lead
- 10m Interconnecting Leads
- Gas Regulator/Flowmeter
- Drive Rollers: 0.9/1.2mm "V" groove; 0.9/1.2mm knurled (gasless, flux cored)
- Primary Voltage: 380/415 Vac, 50 Hz 3 Phase
- Rated Primary Current: 15 Amps
- Max. Primary Current: 23 Amps
- Recommended Generator kVa: 16.5 kVA
- Rated Output @ 40C (10min): 355 A, 32 V, 40%, Duty Cycle, 225 A, 25.3 V, 100%, Duty Cycle
- Welding Current Range: 30 - 355 Amps
- Wire Size Range (mm): 0.6 - 1.2 solid, 0.8 - 1.6 cored